StudentShare
Contact Us
Sign In / Sign Up for FREE
Search
Go to advanced search...
Free

Understanding the Jominy and Quench Test - Report Example

Cite this document
Summary
This report "Understanding the Jominy and Quench Test" contains two reports: the first is a laboratory experiment on the Jominy end-quench test performed to explore the relationship between hardenability and composition of different steels. Three samples were tested and their results were compared…
Download full paper File format: .doc, available for editing
GRAB THE BEST PAPER95.8% of users find it useful

Extract of sample "Understanding the Jominy and Quench Test"

Abstract This paper contains two reports: the first is a laboratory experiment on the Jominy end-quench test performed to explore the relationship between hardenability and composition of different steels. Three samples were tested and their results were compared to each other and used to the above relationship. The second is on CNC machining and the comparison of their performance with conventional machining. A CNC milling process was observed, recorded and its differences noted in comparison to the conventional machining process. The advantages of CNC machining was therefore noted and discussed. Abbreviations and terminology Quench – cooling (with water in this paper) HRC – Rockwell C scale obtained by exerting an indentation pressure of 150kgf using a 120⁰ diamond cone indenter CNC – Computer Numerical Control Introduction The hardenability of metals or their alloys is defined as the depth up to which the sample being tested is hardened after going through a standardized process of heat treatment. This can be tested using a variety of methods such as the Rockwell, Leeb, Vickers, Meyer, and Brinell. This experiment will employ the Rockwell hardness testing to test 3 sample of steel for their hardenability (Kalpakjian, 1989). Hardenability in this test will be measured as the depth to which the sample being tested can be indented using the Jominy end-quench test. It measures how deep into the sample it is possible to achieve a certain hardeness. Hardness units for this test will be in in HRC which is a Rockwell scale obtained by exerting an indentation pressure of 150kgf using a 120⁰ diamond cone indenter(Kalpakjian, 1989). The three test sample hardenability results will be compared against each other . Hardenability A work piece’s hardenability is its capacity to, under specified conditions, harden in depth. When quenched, the surface in contact with the water (quenched end) cools and becomes even in terms of crystalline structure. The rest of the sample that is not in contact with water does not cool as fast as the quenched end, and the hardenability therefore varies along the length of the work piece (Kalpakjian, 1989). This hardenability is a function of the ferrous alloy’s carbon content. When heated to a certain temperature, the steel sample is changes into austenite which on cooling transforms into a small amount of martensite at a specified depth below the surface. The cooling process is referred to as quenching and is done using a jet of room temperature water splashed on one end of the steel cylinder. After quenching a flat surface is ground on the test sample and hardness measured starting from the quenched end on a specified interval. The readings are plotted on the hardenability graph. The farther away from the quenched end the hardness extends, the higher the hardenability of the sample being tested (Kalpakjian, 1989). The quench and temper treatment of steal uses these principles to harden steel in order to give its martensite microstructure the optimum mix of strength and toughness. Without tempering, martensite is brittle, even though it is hard. If the cooling rate is not fast enough, materials other than martensite may form such as pearlite, ferrite, or bainite. The higher the proportion of martensite formed on cooling a steel sample, the higher its hardenability. The higher the hardenability of a material, the better it is suited for use in big high strength components like pistons for rock breakers and aircraft undercarriages among others. The lower its hardenability, the higher its suitability for smaller components like shears or chisels (Gliner & Vybornov, 2013). The Jominy End-Quench Test The Jominy end-quench test was named for Walter E. Jominy (1893-1976) who invented the test in conjunction with A.L. Boegehold. It is a standard measure of the hardenability of steel (test, n.d). A laboratory experiment was conducted to explore the relationship between hardenability and composition of different steels. For this experiment, three samples were tested each measuring 1” in diameter and 4” in length. The samples were austenitized by heating up to a temperature above 850 but not exceeding 900⁰C for at least 20 minutes. The samples were then quenched using water at 24⁰C for 10 minutes then cooled completely in a cooling tank. A flat surface was ground along the length of each test sample at a depth of 0.015” for the purposes of removing decarburised material. Rockwell C Hardness was then measured from the quenched end at an interval of 1.6mm (or 1/16”) up to a length of 2”. Readings below 20HRC were discarded. The same procedure was followed for each sample. The results were then tabulated and a Jominy curve plotted for each sample. Results Three Jominy curves were plotted for the three samples as shown in the three graphs below. The three samples were numbered as 661, 992, and 893. Figure 1: Jominy curves for the three test samples plotted against distance (mm) from the quenched end Table 1: sample 661 SAMPLE 661 Distance (mm) from quenched end HRC Microstructure justification 0 52 martensite cooling rate 10-20 ⁰C/s, HRC >50 25.5 22.2 Ferrite & pearlite cooling rate 10-20 ⁰C/s, HRC >15 but 15 but 27 25.5 37.3 pearlite cooling rate 10-20 ⁰C/s, HRC >27 44.7 32.2 pearlite cooling rate 10-20 ⁰C/s, HRC >27 SAMPLE 893 Distance (mm) from quenched end HRC Microstructure justification 0 53.8 martensite cooling rate 10-20 ⁰C/s, HRC >50 25.5 50.2 martensite cooling rate 10-20 ⁰C/s, HRC >50 50.8 48.6 Martensite & pearlite cooling rate 10-20 ⁰C/s, HRC >40 but Read More

The higher the proportion of martensite formed on cooling a steel sample, the higher its hardenability. The higher the hardenability of a material, the better it is suited for use in big high strength components like pistons for rock breakers and aircraft undercarriages among others. The lower its hardenability, the higher its suitability for smaller components like shears or chisels (Gliner & Vybornov, 2013). The Jominy End-Quench Test The Jominy end-quench test was named for Walter E. Jominy (1893-1976) who invented the test in conjunction with A.L. Boegehold.

It is a standard measure of the hardenability of steel (test, n.d). A laboratory experiment was conducted to explore the relationship between hardenability and composition of different steels. For this experiment, three samples were tested each measuring 1” in diameter and 4” in length. The samples were austenitized by heating up to a temperature above 850 but not exceeding 900⁰C for at least 20 minutes. The samples were then quenched using water at 24⁰C for 10 minutes then cooled completely in a cooling tank.

A flat surface was ground along the length of each test sample at a depth of 0.015” for the purposes of removing decarburised material. Rockwell C Hardness was then measured from the quenched end at an interval of 1.6mm (or 1/16”) up to a length of 2”. Readings below 20HRC were discarded. The same procedure was followed for each sample. The results were then tabulated and a Jominy curve plotted for each sample. Results Three Jominy curves were plotted for the three samples as shown in the three graphs below.

The three samples were numbered as 661, 992, and 893. Figure 1: Jominy curves for the three test samples plotted against distance (mm) from the quenched end Table 1: sample 661 SAMPLE 661 Distance (mm) from quenched end HRC Microstructure justification 0 52 martensite cooling rate 10-20 ⁰C/s, HRC >50 25.5 22.2 Ferrite & pearlite cooling rate 10-20 ⁰C/s, HRC >15 but 15 but 27 25.5 37.3 pearlite cooling rate 10-20 ⁰C/s, HRC >27 44.7 32.2 pearlite cooling rate 10-20 ⁰C/s, HRC >27 SAMPLE 893 Distance (mm) from quenched end HRC Microstructure justification 0 53.

8 martensite cooling rate 10-20 ⁰C/s, HRC >50 25.5 50.2 martensite cooling rate 10-20 ⁰C/s, HRC >50 50.8 48.6 Martensite & pearlite cooling rate 10-20 ⁰C/s, HRC >40 but

Read More
Cite this document
  • APA
  • MLA
  • CHICAGO
(Understanding the Jominy and Quench Test Report Example | Topics and Well Written Essays - 1750 words, n.d.)
Understanding the Jominy and Quench Test Report Example | Topics and Well Written Essays - 1750 words. https://studentshare.org/physics/2065157-cnc-and-jominy
(Understanding the Jominy and Quench Test Report Example | Topics and Well Written Essays - 1750 Words)
Understanding the Jominy and Quench Test Report Example | Topics and Well Written Essays - 1750 Words. https://studentshare.org/physics/2065157-cnc-and-jominy.
“Understanding the Jominy and Quench Test Report Example | Topics and Well Written Essays - 1750 Words”. https://studentshare.org/physics/2065157-cnc-and-jominy.
  • Cited: 0 times

CHECK THESE SAMPLES OF Understanding the Jominy and Quench Test

Two Psychometric Tests

CPP, the institute from where the test can be officially obtained, claims that it administers over 2 million assessments annually, which is the largest number for any psychometric assessment.... MBTI, as regarded by many professionals and experts, is the best and most trusted personality assessment tool used all over the world....
11 Pages (2750 words) Essay

Life Lessons from the Brady Bunch

Culture is a learned aspect of the society.... It is a social asset and all members of society share its elements.... In the contemporary setting, these cultural elements are preserved and disseminated through the mass media from one individual to another and also from one generation to another.... ...
6 Pages (1500 words) Essay

Conflict Resolution at the Place of Business

The negotiation presented aspects of understanding and coming to agreement which are common in global negotiations, but added some elements of international culture and differing attitudes to negotiating strategy and tactics. ... The lessons learned included general negotiating skills, and an increased understanding of how cultural predispositions and assumptions can add complexity to a set of negotiations.... Although FrenchCo was a smaller company than USCo, it was nevertheless a leader due to its history, its emphasis on quality, and its deep understanding of the science of microbiology....
5 Pages (1250 words) Essay

French laundry ( marketing analysis)

Thomas Keller established this French restaurant in the year 1978.... The restaurant ranked in the top 50 in the Worlds Restaurant Magazine List.... In the year 2006 the restaurant.... ... ... The restaurant offers a wide range of cuisines but is predominated by French and contemporary American flavour....
4 Pages (1000 words) Essay

What Government Agencies Do and Why They Do It

The author examines the books "Managing Human Behavior in Public" and "Nonprofit Organizations and Bureaucracy: What Government Agencies Do And Why They Do It" which provide us with a deep and valued into the working, structure, and function of varied organizations.... .... ... ... Wilson's organizational politics is not similar because the 'federal government are staffed with bureaucrats who are more liberal than the population at large'....
7 Pages (1750 words) Term Paper

Food Politics: How the Food Industry Influences Nutrition and Health

However influenced by the negative press of high sugar content and leading to obesity, the market value of fruit juice is Atlantic quench operates in the fruit juice segment with the objective of maintain and attracting more consumers through offering them greater range of benefits present in their manufactured fruit juice products.... The paper analyses the existing fruit juice markets of the US and the UK so as to conduct a marketing plan for growth for Atlantic quench in next year....
15 Pages (3750 words) Essay

Marketing Plan for Atlantic Quench

The current paper is an effort towards understanding the market conditions existing in the fruit juice sector in the U.... PEST analysis is a useful tool for understanding the conditions existing in the external environment.... This paper ''Marketing Plan for Atlantic quench'' tells us that The fruit juice industry across the globe is seen to undergo a trend of sustained growth.... The following report in general deals with the market analysis of Atlantic quench....
17 Pages (4250 words) Essay

The Jominy End-Quench Experiment to Understand Various Aspects and Process in the Metal Structural Industry

"Jominy End-Quench Experiment to Understand Aspects and Process in the Metal Structural Industry" paper focuses on Jominy end-quench test the purpose of twhich was to realize the exploration of the relationship that exists between the composition and hardenability of various forms of steel.... The Jominy end quench test is very useful in the determination of steel hardenability.... he aim of the Jominy end-quench test was to identify and confirm the achievement correct hardenability in accordance with what is already stated or in the record as the current hardenability data for steel....
8 Pages (2000 words) Lab Report
sponsored ads
We use cookies to create the best experience for you. Keep on browsing if you are OK with that, or find out how to manage cookies.
Contact Us